Acrylic powder coating

Surface Finish Options Overview

Made of polyester resin and acrylic resin as the main raw materials

Features:

–Smooth and delicate surface, good hand feel

—Good adhesion and good impact resistance

—Excellent weather resistance

Application:

—Outdoor lighting, outdoor furniture, aluminum ceilings, aluminum profiles, etc.

Product series:

—Can be made into a variety of low-gloss and colorful colors, the specific gloss color is subject to user requirements

—Good anti-yellowing property

Application parameters:

Curing time: 200℃×10–15 minutes

Spraying method: High-voltage electrostatic spraying 60-80 KV

Recommended film thickness: 60-80 um

The above tests all use 0.8mm degreased and rusted cold-rolled steel plates, the coating thickness is 40-80um, and the performance indicators of the coating will vary slightly with the gloss.

This product does not contain arsenic, selenium, lead, hexavalent chromium, mercury, antimony, cadmium, and other heavy metals, and complies with RoHS requirements.

Storage conditions: Store in a dry, ventilated room at around 25°C, avoid direct sunlight. Under this condition, the powder can be stored for 6-12 months. If it exceeds the expiration date, it can be re-tested. If the results meet the requirements, it can still be used.

FAQ

1. What is Powder Coating?

Powder coating is a dry finishing process used to apply a protective and decorative coating on metal or other surfaces. Instead of using liquid paint, fine powder particles (usually made of polyester, epoxy, or hybrid resins) are electrostatically charged and sprayed onto a conductive surface. The coated object is then baked in an oven, where the powder melts, flows, and cures into a smooth, durable finish.

Key features:

Durable, hard finish

Resistant to scratches, corrosion, and UV

Environmentally friendly (no VOCs)

2. Benefits of Powder Coating

Powder coating offers several advantages over traditional liquid painting:

Durability: Resistant to chipping, scratching, fading, and wear.

Corrosion Protection: Provides excellent protection against rust and chemicals.

Environmentally Friendly: No volatile organic compounds (VOCs) and minimal waste.

Efficiency: Overspray can be collected and reused, up to 99% material utilization.

Uniform Finish: Smooth, even coating without runs or drips.

Cost-Effective: Single-coat systems can achieve high film thickness, reducing labor and energy.

Aesthetic Variety: Wide range of colors, textures, and effects.

3. What Temperature to Cure Powder Coating

The curing temperature depends on the type of powder used:

Epoxy powder: ~160–200°C (320–392°F)

Polyester powder: ~180–210°C (356–410°F)

Hybrid (Epoxy-Polyester) powder: ~180–200°C (356–392°F)

Typical curing time: 10–20 minutes depending on thickness and oven type.

Always follow the powder manufacturer’s specifications for best results.

4. Process for Powder Coating

The powder coating process usually follows these steps:

Surface Preparation:

Clean the surface thoroughly (remove oil, grease, rust, or dirt)

Methods: chemical cleaning, sandblasting, or phosphating

Pre-Treatment:

Apply a conversion coating or primer if needed to improve adhesion

Powder Application:

Spray the powder using an electrostatic spray gun or fluidized bed

Curing:

Bake the coated object in an oven at the recommended temperature for the powder type

The powder melts and forms a continuous, smooth film

Cooling & Inspection:

Let the coated item cool

Inspect for defects, uniform coverage, and desired thickness

5. How to Spray Powder Coat

Equipment Needed:

Electrostatic spray gun

Compressed air supply

Powder feed hopper or container

Grounding of the object

Steps:

Ground the object: Ensures the charged powder is attracted to the surface.

Spray evenly: Hold the gun 6–12 inches from the surface, moving in smooth, overlapping strokes.

Apply sufficient powder: Ensure full coverage without excessive buildup.

Cure immediately: Transfer the sprayed item to the curing oven to fuse the powder into a solid coating.

Tips:

Maintain consistent speed and distance while spraying.

Use proper ventilation to reduce airborne powder accumulation.

Test a small area to check film thickness and color before full application.